Skip to content
LatticeMLS, Home

Add your earlier progress to your account?

From before you signed in, this browser has:

Which plan do you want to keep?

You changed your plan before signing in, and those changes don't match the plan saved on your account.

SettingSaved planPlan changes

Study progress is waiting to be saved

Serial dilutions

14 min

Skills you'll build3 skills
  • Calculate a cumulative dilution factor
  • Calculate the destination concentration in a serial dilution step
  • Predict how a transfer or diluent volume error changes a serial dilution

At the bench: Prepare a dilution using the required sample and diluent volumes

Try first

Try first

A serum is diluted 1:4, and then the mixed 1:4 tube is diluted 1:5. Which factor converts a reading on the second tube back to the serum?

Right. Keep going to follow the reasoning.

Keep going to see the reasoning.

Keep going to see the reasoning.

Keep going to see the reasoning.

Get the idea

How a serial dilution is made

In a serial dilution each tube is made from the tube before it, after that tube has been mixed. Each step dilutes a solution that earlier steps have already diluted.

Each step has its own factor, taken from the volumes put into that tube:

step factor = (transfer volume + diluent volume) ÷ transfer volume

The tube's concentration comes from its source, the tube just before it:

destination concentration = source concentration ÷ step factor

Multiply the step factors

The total factor for any tube, compared with the original, is the product of every step factor up to and including that tube.1,2 Step factors are never added. Two 1:5 steps leave one twenty-fifth of the original, so correcting a result by 5 + 5 = 10 would give a value 2.5 times too low.

An example series starting at 240 mg/L:

TubeTransfer + diluent (µL)Step factorTotal factorConcentration (mg/L)
1500 + 50022120
2250 + 7504830
3200 + 8005406

Tube 3 is 30 mg/L ÷ 5, using tube 2 as its source. Dividing the original 240 mg/L by 5 would give 48 mg/L, which is not the concentration of any tube in this series.

When one volume is off

Calculate the factors from the volumes that were pipetted. If one transfer or diluent volume is wrong:

  • That tube's step factor changes.
  • Every later total factor is a product that includes it, so the error is carried into every later tube even when the later steps are pipetted correctly.2
  • Calculations with the planned factors give the wrong concentration for that tube and every tube after it.

Remake the affected tube and every tube after it. Keep the tubes made before the slip.

Follow the bench demonstration

Sources for this step
References
  1. Bishop ML, Fody EP, Van Siclen C, Mistler JM, Moy M. Clinical Chemistry: Principles, Techniques, and Correlations. 9th ed. Jones & Bartlett Learning; 2023.
  2. Kingston University. Concentration of solutions: serial dilution: overview. Reviewed March 31, 2021. Accessed September 23, 2026.

Watch one

A tenfold series is planned from a solution at 80 mg/L: three tubes, each 100 µL of the previous tube plus 900 µL of diluent.

  • Tube 1 was made with 100 µL of the solution and only 400 µL of diluent.
  • Tubes 2 and 3 were made as planned.

What is the concentration in tube 3, and what do you do?

  1. Use tube 1's actual volumes: 100 µL + 400 µL = 500 µL, so its step factor is 500 ÷ 100 = 5, half the planned 10.

    The step factor comes from the volumes in the tube.

  2. Keep the later step factors at 10 and 10.

    Tubes 2 and 3 were pipetted as planned, so their step factors are unchanged.

  3. Multiply the actual step factors: 5 × 10 × 10 = 500. The plan assumed 1,000.

    Each later tube was made from the one before, so the first step's factor is part of every later total factor.

  4. Tube 3 contains 80 mg/L ÷ 500 = 0.16 mg/L, twice the intended 0.08 mg/L.

    The concentration is calculated from the total factor of the tubes as made.

  5. Remake tube 1 and then tubes 2 and 3 from it.

    The pipetting error affects every tube made after it.

Tube 3 contains 0.16 mg/L at a total factor of 500. Remake tube 1 and every tube after it.

Practice this skill

Your turn

Problem 1 of 3 · Hints available

A specimen is diluted 1:5, and that diluted sample is diluted 1:5 again. Which dilution factor converts a result measured on the second tube into the original specimen concentration?

Incorrect. Factor 5 reverses only the second dilution, so it gives the concentration in the first tube. Multiply by another factor of 5 to recover the original concentration.

Incorrect. Adding the factors gives 10, but the second dilution acts on a mixture that is already one fifth of the original concentration. One fifth of one fifth is one twenty-fifth, so the factors multiply: 5 × 5 = 25.

Correct. Each 1:5 step leaves one fifth of the previous concentration, and one fifth of one fifth is one twenty-fifth. The result measured on the second tube multiplied by 25 gives the original specimen concentration.

Hint
  1. The second tube is made from the first tube, which is already more dilute than the specimen.
  2. After the first step the tube has one fifth of the specimen's concentration. The second tube has one fifth of that.
  3. Combine the two step factors the way the fractions combine.

Review Serial factors multiply

Problem 2 of 3 · Hints available

A solution at 180 mg/L is diluted 1:5 into tube 1, which is mixed. You then transfer 200 µL of tube 1 into 400 µL of diluent to make tube 2. What is the concentration in tube 2?

Hint
  1. Tube 2's source is tube 1. Find tube 1's concentration first.
  2. Tube 1 is 180 ÷ 5 = 36 mg/L. Now find tube 2's step factor from its volumes.
  3. The step factor is the whole volume in tube 2 divided by the part transferred.
Show the answer

12 mg/L

Tube 1 is 180 ÷ 5 = 36 mg/L. Tube 2 holds 200 + 400 = 600 µL, so its step factor is 600 ÷ 200 = 3, and 36 mg/L ÷ 3 = 12 mg/L.

Review Serial factors multiply

Problem 3 of 3 · On your own

A twofold series of three tubes is planned, each 500 µL of the previous tube plus 500 µL of diluent. Tube 2 is made with 500 µL of tube 1 and 1,000 µL of diluent. Tubes 1 and 3 are made as planned. Which total factor describes tube 3?

Eight is 2 × 2 × 2, the plan. Tube 2's step factor is 1,500 ÷ 500 = 3, and tube 3 was made from tube 2, so the plan's factor no longer applies.

Used the intended factor after preparing different volumes

A transfer of 200 µL into 900 µL of diluent gives a factor of 1,100 ÷ 200 = 5.5, short of the intended 10, and the error carries into every later tube. After two more tenfold steps the total factor is 550, where the plan called for 1,000. Using the intended factor misstates every downstream concentration.

Seven is 2 + 3 + 2. Each tube divides the concentration of the tube before it, so the step factors multiply.

Added the dilution factors

Each step acts on the concentration the step before it produced, so two 1:5 steps leave one twenty-fifth of the original. Adding the factors gives 10, and a result corrected by 10 is 2.5 times too low.

The step factors are 2, then 1,500 ÷ 500 = 3, then 2, and 2 × 3 × 2 = 12.

Four leaves out tube 2 altogether. Tube 3 was made from tube 2, so tube 2's step counts.

Review Unequal steps and volume errors

Use it

Optional for this step.

For reference