Skip to content
LatticeMLS, Home

Add your earlier progress to your account?

From before you signed in, this browser has:

Which plan do you want to keep?

You changed your plan before signing in, and those changes don't match the plan saved on your account.

SettingSaved planPlan changes

Study progress is waiting to be saved

R-4s, 10x and finding the cause

14 min

Skills you'll build3 skills
  • Recognize an R-4s violation within one run
  • Recognize a 10x violation in consecutive same-side controls
  • Match a QC shift, trend, or random error to its likely causes

At the bench: Review QC before releasing results

Try first

Try first

Two glucose control levels are run twice a day. Each result's distance from its own mean:

RunLevel 1Level 2
Yesterday, 15:00+2.5 SD+0.3 SD
Today, 07:00−0.2 SD−2.3 SD

Is R-4s met?

Keep going to see the reasoning.

Keep going to see the reasoning.

Right. Keep going to follow the reasoning.

Keep going to see the reasoning.

Get the idea

Two more rules complete the usual Westgard multirule set, and each detects a different type of error.

R-4s within one run

  • The R-4s rule is met when one control is above +2 SD and another in the same run is below −2 SD, a spread of more than 4 SD.
  • Controls measured together share the same reagent and calibration. When they move in opposite directions in the same run, the cause is random error.
  • R-4s applies within one run. Pairing results from different runs includes between-run variation in the comparison.1,2

The 10x rule

  • The 10x rule is met when ten consecutive controls fall on the same side of the mean, even if every one of them is inside ±2 SD.
  • A procedure in control gives about half its results on each side of the mean, so ten in a row on one side indicates a small systematic shift.
  • Some QC plans use 8x or 9x for this check, and the plan specifies whether the count includes results across levels as well as across runs.1,3

Investigating the cause

When a rule rejects the run, the type of error it detects indicates where to look first.2,3

Error typeRulesCauses to check first
Random1-3s, R-4sBubbles, a clot or short sample in the probe, uneven pipetting, electrical noise
Systematic2-2s, 4-1s, 10x, a shift or trendReagent lot or deterioration, calibration, temperature, a failing lamp or electrode

Corrective action and lookback

Rerunning the same control until it passes does not identify or correct the fault. Work in this order:2,4

  1. Correct the cause.
  2. Rerun the controls.
  3. Release patient results only after QC is acceptable.
  4. Review the patient results from the rejected run and every result reported since the last acceptable run. Repeat those the error could have changed.

A sequence rule such as 10x is met only after a shift has lasted several runs, so the review goes back to the run where the shift began.3

Follow the bench demonstration

Sources for this step
References
  1. Westgard JO. Westgard rules and multirules. Westgard QC. Accessed September 23, 2026.
  2. Westgard JO. QC: the multirule interpretation. Westgard QC. Accessed September 23, 2026.
  3. Clinical and Laboratory Standards Institute. Statistical Quality Control for Quantitative Measurement Procedures: Principles and Definitions. 4th ed. CLSI guideline C24Ed4E. Clinical and Laboratory Standards Institute; 2016.
  4. Centers for Medicare & Medicaid Services. 42 CFR §§493.1256 and 493.1282. Electronic Code of Federal Regulations. Accessed September 23, 2026.

Watch one

A BUN level 2 control has a mean of 50 mg/dL and an SD of 2 mg/dL. Its last ten runs, oldest first:

Run12345678910
Result50.8 mg/dL51.5 mg/dL50.4 mg/dL52.2 mg/dL51.0 mg/dL51.8 mg/dL50.6 mg/dL52.4 mg/dL51.2 mg/dL51.6 mg/dL

A new calibrator lot was put into use before run 1. What do you decide, and where do you look?

  1. Check 1-2s: the +2 SD limit is 54 mg/dL and the highest result is 52.4 mg/dL, so there is no warning.

    A warning would send you to the other rules, so it is checked first.

  2. Check 4-1s: only runs 4 and 8 are beyond the +1 SD limit of 52 mg/dL, and they are not consecutive, so 4-1s is not met.

    Results within ±2 SD can still violate the sequence rules.

  3. Check 10x: all ten results are above 50 mg/dL, so 10x is met and the run is rejected.

    Ten results in a row on one side of the mean indicate a small shift.

  4. Name the error type: systematic, so bubbles and pipetting are not the first place to look.

    Every sequence rule detects systematic error, which shifts every result in the same direction.

  5. Check the calibration first: the new calibrator lot was put into use just before run 1, when the results moved above the mean.

    The shift began when something common to every result changed.

Reject the run for 10x and investigate the calibration made with the new calibrator lot. Once QC is acceptable, review the patient BUN results reported since the new lot went into use, just before run 1.

Practice this skill

Your turn

Problem 1 of 3 · Hints available

Two controls in the same run are +2.4 SD and −2.3 SD from their respective means. Which rejection rule is met?

Incorrect. 2₂s requires consecutive results on the same side beyond 2 SD. These deviations point in opposite directions.

Correct. One result is above +2 SD and the other below −2 SD in the same run. Their separation is 4.7 SD.

Incorrect. Neither result exceeds a 3 SD limit. Their within-run separation meets R₄s.

Hint
  1. Both results come from the same run.
  2. One result is above +2 SD and the other is below −2 SD.
  3. Look for the rule that compares two controls moving in opposite directions within one run.

Review Multirule interpretation

Problem 2 of 3 · Hints available

A calcium level 2 control has a mean of 11.6 mg/dL and an SD of 0.2 mg/dL. Its last ten runs:

Run12345678910
Result11.7 mg/dL11.8 mg/dL11.7 mg/dL11.9 mg/dL11.7 mg/dL11.8 mg/dL11.7 mg/dL11.8 mg/dL11.9 mg/dL11.7 mg/dL

Which rule, if any, is met?

4-1s needs four consecutive results beyond +1 SD, which is 11.8 mg/dL. Only runs 4 and 9 are beyond it.

All ten results are above the 11.6 mg/dL mean. Ten in a row on one side meets 10x and indicates a small systematic shift, even though every result is within ±2 SD.

A stable procedure puts about half its results below the mean. Ten in a row above it meets 10x, however small each difference looks.

Ignored ten controls on the same side of the mean

Ten consecutive results on one side of the mean violate the 10x rule even when all fall within ±2 SD, as with glucose controls from 122 to 127 mg/dL with a mean of 120 mg/dL and an SD of 4 mg/dL. Accepting the run because no single value is out of range lets a shift reach patient results.

No result goes beyond +2 SD, 12.0 mg/dL, so there is no warning. The sequence meets a rule with no warning.

Hint
  1. No result goes beyond 12.0 mg/dL, the +2 SD limit.
  2. Count how many results fall above the mean.

Review Multirule interpretation

Problem 3 of 3 · On your own

An ALT level 2 control drifts upward over six days: +0.3, +0.8, +1.2, +1.6, +1.9 and +2.3 SD. Level 1 drifts the same way. The reagent cartridge was loaded on day 1, and its onboard stability ends tomorrow. The run is rejected for 4-1s. What do you check first?

Those are random causes, which scatter results both ways. A steady climb on both levels is systematic, and a cartridge near the end of its onboard stability fits it.

Looked for random causes behind a shift

A shift or trend moves results in one direction, which indicates systematic error from causes such as reagent deterioration, a calibration problem, or a temperature change. Checking only for random causes such as bubbles or pipetting errors leaves the fault in place, and the next run fails the same way.

Both levels rise a little each day since the cartridge was loaded, a trend that indicates a systematic cause. Reagent deterioration near the end of onboard stability, and the calibration made with it, are the first things to check.

A passing rerun does not explain the trend, and the cause would still be present for the next run. Find and correct the cause first.

Review Levey-Jennings charts

Use it

Optional for this step.

For reference