Unit conversions, the median and absorbance
13 min
Skills you'll build3 skills
- Convert between compatible mass, volume, and amount concentration units
- Calculate the median of an ordered set of results
- Convert percent transmittance to absorbance
Try first
Get the idea
Three basic calculations are used throughout laboratory work: moving a result between units, finding the middle of a set of results, and reading absorbance from a photometer.
Units
A concentration is an amount of substance in a volume, and both parts of the unit can change.
- Change the volume first. A liter is 10 deciliters, so a result in mg/dL becomes mg/L when it is multiplied by 10.1
- Then change the mass with the molar mass, the mass of one millimole of the substance:
mmol/L = mg/L ÷ molar mass (mg/mmol)
Glucose has a molar mass of 180.16 mg/mmol, so 1,080 mg/L of glucose is 1,080 ÷ 180.16 = 5.99 mmol/L.
The number changes every time the unit does. A result relabeled without changing its number is wrong:2
- by a factor of 10 for a volume change
- by the molar mass for a mass change
Each laboratory reports in the units it has validated, with its own stated factors.
The median
Put the results in rank order and take the middle one.
- When the count is odd there is one middle value.
- When the count is even there are two, and the median is their average. For four chloride results of 98, 101, 104 and 109 mmol/L, it is (101 + 104) ÷ 2 = 102.5 mmol/L.
The median depends on rank, so one extreme result changes it far less than it changes the mean.3
Absorbance
A photometer compares the light leaving a sample with the light entering it.
- That fraction is the transmittance, T.
- The percent transmittance, %T, is 100 × T.
- Absorbance is the negative base-10 logarithm of the fraction.
A = −log₁₀(T) = 2 − log₁₀(%T)
The two forms give the same answer when each uses its own input:2,4
- At 10%T, T is 0.10 and A = 1.00.
- At 100%T, no light was absorbed and A = 0.
- Taking the logarithm of the percent in the first form gives a negative absorbance, which shows the percent was used in the fraction form.
Follow the bench demonstration
Sources for this step
References
- Thompson A, Taylor BN. Guide for the Use of the International System of Units (SI). NIST Special Publication 811. 2008 ed. National Institute of Standards and Technology; 2008.
- Bishop ML, Fody EP, Van Siclen C, Mistler JM, Moy M. Clinical Chemistry: Principles, Techniques, and Correlations. 9th ed. Jones & Bartlett Learning; 2023.
- National Institute of Standards and Technology. Measures of location. NIST/SEMATECH e-Handbook of Statistical Methods. Accessed September 23, 2026.
- International Union of Pure and Applied Chemistry. Beer–Lambert law. In: Compendium of Chemical Terminology. 5th ed. Online version 5.0.0. International Union of Pure and Applied Chemistry; 2025. doi:10.1351/goldbook.B00626
Watch one
A glucose result is 90 mg/dL. Your laboratory's comparison table lists glucose in mmol/L with a molar mass of 180.16 mg/mmol. What is the result in mmol/L, to three significant figures?
- Change the volume: 90 mg/dL × 10 = 900 mg/L.
The result is needed per liter, so the volume changes from deciliters to liters first.
- Divide by the molar mass: 900 ÷ 180.16 = 4.9956 mmol/L.
Each millimole of glucose weighs 180.16 mg, so the number of millimoles is the mass divided by that.
- Round the final value to three significant figures: 5.00 mmol/L.
Rounding once, at the end, keeps the intermediate error out of the reported value.
- Check the size: 5.00 is smaller than 900, as it must be.
A molar mass above 1 mg/mmol always makes the amount smaller than the mass, so an answer larger than the mass means the mass was multiplied by the molar mass.
Your turn
Review missed questions
For reference
Sources checked
The rest of this step has a short briefing, a demonstration at the bench and 3 practice problems.
Free account: keep your progress and get review reminders. Have one? Sign in