Skip to content
LatticeMLS, Home

Add your earlier progress to your account?

From before you signed in, this browser has:

Which plan do you want to keep?

You changed your plan before signing in, and those changes don't match the plan saved on your account.

SettingSaved planPlan changes

Study progress is waiting to be saved

Control statistics

13 min

Skills you'll build4 skills
  • Calculate the mean of control measurements
  • Calculate standard deviation from stated control limits and state its unit
  • Calculate coefficient of variation from a mean and standard deviation
  • State the share of control results expected within 1, 2, and 3 SD of the mean

Try first

Try first

A glucose control at level 1 has a mean of 100 mg/dL and an SD of 4 mg/dL. The level 2 control has a mean of 300 mg/dL and an SD of 9 mg/dL. Which level shows the smaller imprecision relative to its concentration?

Keep going to see the reasoning.

Keep going to see the reasoning.

Right. Keep going to follow the reasoning.

Keep going to see the reasoning.

Get the idea

Mean, SD, variance and CV

A control material is measured repeatedly, and its results spread around a central value. Four statistics describe those results, and every QC rule is based on them.

  • The mean is the arithmetic average: add the results and divide by how many there are.
  • The standard deviation (SD) describes how far results typically fall from the mean. It is expressed in the analyte's own unit, such as mmol/L or mg/dL.
  • The variance is the SD squared.1
  • The coefficient of variation (CV) expresses the SD as a percentage of the mean, so levels and methods can be compared:

CV (%) = SD ÷ mean × 100

Because the SD is in concentration units, a larger SD at a higher concentration can still represent better precision.

Calculating SD from the limits

A control sheet often lists only the limits. Limits of ±2 SD run from 2 SD below the mean to 2 SD above it.

  • The mean is the midpoint.
  • The whole interval is 4 SD wide, so 1 SD is the width divided by 4.
  • Dividing by 2 gives an SD twice the true value and places every limit too far from the mean.2

SD bands

When the results of a stable procedure follow a Gaussian distribution, fixed percentages fall within each band:3

Band around the meanResults insideResults outside
±1 SD68.3%31.7%
±2 SD95.4%4.6%
±3 SD99.7%0.3%

These percentages explain how the rules treat each band:4

  • A control beyond 2 SD occurs about once in every 22 results from a stable procedure. A run with two control levels gives two chances, so about 9% of good runs show one. A single result beyond 2 SD is therefore a warning to check the other rules.
  • A result beyond 3 SD occurs by chance about 3 times in 1,000, so it is rare enough to reject the run.

Laboratories set each control's mean and SD from their own repeated measurements of one control lot, collected over many runs. The examples here use a handful of results to show the arithmetic. That is far too few results to show whether the distribution is Gaussian.2

Follow the bench demonstration

Sources for this step
References
  1. National Institute of Standards and Technology. Measures of scale. NIST/SEMATECH e-Handbook of Statistical Methods. Accessed September 23, 2026.
  2. Clinical and Laboratory Standards Institute. Statistical Quality Control for Quantitative Measurement Procedures: Principles and Definitions. 4th ed. CLSI guideline C24Ed4E. Clinical and Laboratory Standards Institute; 2016.
  3. National Institute of Standards and Technology. What do we mean by "normal" data?. NIST/SEMATECH e-Handbook of Statistical Methods. Accessed September 23, 2026.
  4. Westgard JO. Westgard rules and multirules. Westgard QC. Accessed September 23, 2026.

Watch one

A new sodium control lot arrives with laboratory-established limits of 147.0 to 153.0 mmol/L, stated as ±2 SD. Find the mean, the SD, the CV and the ±3 SD limits.

  1. Take the midpoint: (147.0 + 153.0) ÷ 2 = 150.0 mmol/L.

    The ±2 SD limits are the same distance on either side of the mean.

  2. Divide the width by 4: (153.0 − 147.0) ÷ 4 = 6.0 ÷ 4 = 1.5 mmol/L.

    From the lower limit to the upper limit is 2 SD down plus 2 SD up, 4 SD in all.

  3. Divide the SD by the mean: 1.5 ÷ 150.0 × 100 = 1.0%.

    The CV expresses the SD as a percentage of the mean.

  4. Add and subtract 3 SD: 150.0 − 4.5 = 145.5 mmol/L and 150.0 + 4.5 = 154.5 mmol/L.

    Every other limit on the chart is a whole number of SDs from the mean.

Mean 150.0 mmol/L, SD 1.5 mmol/L, CV 1.0%, ±3 SD limits 145.5 to 154.5 mmol/L.

Practice this skill

Your turn

Problem 1 of 3 · Hints available

A control's ±2 SD interval is 80 to 110 mg/dL. What is 1 SD?

Correct. The full interval spans 4 SD, from 2 SD below the mean to 2 SD above it. Dividing 30 mg/dL by 4 gives 7.5 mg/dL.

Incorrect. The distance from the mean of 95 mg/dL to either limit is 15 mg/dL, which represents 2 SD. Dividing that distance by 2 gives 7.5 mg/dL.

Incorrect. Subtracting 80 from 110 gives the full width of the interval. That width spans 4 SD, so 1 SD is 30 ÷ 4 = 7.5 mg/dL.

Hint
  1. The lower limit is 2 SD below the mean, and the upper limit is 2 SD above it.
  2. Count the SDs from the lower limit to the upper limit.
  3. Divide the full width of the interval by that count.

Review Statistical control of a measurement procedure

Problem 2 of 3 · Hints available

A stable potassium procedure runs two control levels in every run. About how often will a good run show at least one control beyond ±2 SD by chance alone?

That is the chance of one result beyond ±3 SD. Far more results fall outside ±2 SD.

About 1 result in 22 falls outside ±2 SD. With two controls in the run, the chance for the run is close to double that.

About a third of results fall outside ±1 SD. The ±2 SD band contains 95.4% of results.

Each control has a 4.6% chance of falling outside ±2 SD, and two controls make the chance about 9% for the run. That is why one control beyond 2 SD is a warning and needs the other rules before the run is rejected.

Hint
  1. About 4.6% of single results from a stable procedure fall outside ±2 SD.
  2. Each run gives the procedure two chances to produce one.

Review Statistical control of a measurement procedure

Problem 3 of 3 · On your own

A magnesium control gives five results: 2.0, 2.1, 1.9, 2.0 and 2.0 mg/dL. The SD of these results is 0.07 mg/dL. What is the CV?

Show the answer

3.5 %

The mean is (2.0 + 2.1 + 1.9 + 2.0 + 2.0) ÷ 5 = 10.0 ÷ 5 = 2.00 mg/dL, and the CV is 0.07 ÷ 2.00 × 100 = 3.5%.

Review Statistical control of a measurement procedure

For reference

Sources checked